- Package
- LGA-12
Product overview
QST Sensors QMA6100P is a genuine original component suitable for circuit design and volume procurement. We supply full specifications, datasheets and flexible pricing, supporting both prototype and long-term supply.
- Manufacturer
- QST
- Part number
- QMA6100P
- Category
- Sensors
- Package
- LGA-12
- Condition
- New & Original
- Lifecycle
- Confirm with manufacturer
- Lead time / MOQ
- Confirm with quotation
Technical parameters
36 parametersConstruction
- MCLK = 51.2Khz (All ODR)
- 38
- MCLK = 25.6Khz (All ODR)
- 19
- MCLK = 6.4Khz (All ODR)
- 6
- ULPS
- 5
- Data output rate (ODR)
- 1
- Startup time
- 2 ms
- Wakeup time active mode to the time device is
- 1 ms
- FS=±2g
- 096
- FS=±4g
- 048
- FS=±8g
- 024
- FS=±16g
- 512
- FS=±32g
- 256
- FS=±2g, Normal VDD Supplies
- ±0 %/℃
- Sensitivity tolerance Gain accuracy
- ±4 %
- Zero-g offset FS=±2g, Normal VDD Supplies
- ±80 mg
- Noise density FS=±2g, run state
- 220 /√Hz
- Nonlinearity FS=±2g, Best fit straight line
- 0.5 %FS
- Cross Axis Sensitivity
- 1 %
- Storage Humidity Hstr
- 95 RH
- ESD(HBM) Vhbm
- 000 V
- ESD(CDM) Vcdm
- 500 V
- Shock Immunity
- 000
- Vol_d2
- 0 V
- Internal Pullup Resistor Rpullup
- 190 kohm
- I2C Load Capacitor Cb SDX
- 400 pF
- Crst
- 20 pF
- Trst
- 100 µsec
- Power on Startup Time Tstart
- 10 msec
Performance
- Supply voltage VDD VDD, for internal blocks
- 3.0 V
- Power current MCLK = 12.8Khz (All ODR)
- 10 μA
- Operating temperature
- 85 ℃
- Power Supply Voltage Vddmax
- 5.4 V
- Input Voltage (other than power) Vmax
- 0.2 V
- Storage Temperature Tstr
- 125 ℃
- Digital Output Low Voltage(I2C) Vol_d1 Io=3mA (SDI) *1)
- 0 V
- Leakage Current at Output OFF Ioff SDX
- 10 µA
Specifications & documentation
Use the official manufacturer documentation to verify electrical characteristics, package dimensions and operating limits before design approval.
Frequently asked questions
Common pre-quotation questions and selection notes to help you verify key parameters and sourcing before requesting a quote.
How do I verify the part is genuine / avoid counterfeit?
Buy only from authorized or franchised channels. On receipt, check: (1) laser-etched markings that solvent will not remove; (2) batch / lot code consistent between label and device; (3) original reel or tube packaging; (4) request traceability documents (CoC, date code). For critical parts, third-party X-ray / decapsulation testing is recommended.
How do I read the markings / date code on a chip?
Most active ICs use a 4-digit date code YYWW (year + week, e.g. 2345 = 2023 week 45). The top mark is manufacturer logo + base part number + lot code. For SMD code lookup, search by "marking code + package" on AllDataSheet / Octopart / LCSC.
What does the package code mean (TO-220, SOT-23, QFP…)?
Package codes describe the physical form factor and pin layout — critical when sourcing, because electrically equivalent parts in different packages will not fit the PCB. Common: TO-220 (3-terminal power), SOT-23 (3-pin small signal), DIP / SOIC (through-hole / SMD ICs), QFP / QFN (MCUs, processors).
What if my original model is discontinued (EOL / NRND)?
Three options: (1) the manufacturer’s recommended replacement; (2) franchised distributor legacy stock; (3) a functionally compatible cross-brand part — provided pinout and key parameters match. Always evaluate on a real board before mass swap.
What is the minimum order quantity (MOQ) and lead time?
We support both sample and volume orders. Minimum order quantity, stock availability and lead time are confirmed per inquiry — tell us your model and quantity and we will quote. Sample quantities for design validation are supported.
Can I get the datasheet and samples?
The full datasheet is linked on this page. For parts without a direct datasheet, we can locate the manufacturer document on request. Sample requests are supported — contact us with your model and quantity.
Request confirmation of current stock, date code, packaging, price and delivery terms. Product information does not constitute a binding offer; final specifications are confirmed with your quotation.