- Package
- LFCSP-20
Product overview
Analog / Mixed-Signal IC
- Manufacturer
- ADI
- Part number
- AD8232ACPZ-R7
- Category
- Sensors
- Package
- LFCSP-20
- Condition
- New & Original
- Lifecycle
- Confirm with manufacturer
- Lead time / MOQ
- Confirm with quotation
Technical parameters
44 parametersConstruction
- Common-Mode Rejection Ratio, CMRR VCM = 0.35 V to 2.85 V
- 86 dB
- TOPR
- 80 dB
- VCM = 0.35 V to 2.85 V
- 80 dB
- Power Supply Rejection Ratio PSRR VS = 2.0 V to 3.5
- 90 dB
- Instrumentation Amplifier Inputs
- 3 mV
- DC Blocking Input 1
- 5 µV
- DC Blocking Input1
- 0.05 µV/°C
- Differential
- 10||7.5 GΩ||pF
- Common Mode
- 5||15 GΩ||pF
- Spectral Noise Density f = 1 kHz
- 100 nV/√Hz
- f = 0.5 Hz to 40 Hz
- 14 µVp-p
- DC Differential Input Range
- +300 mV
- Output Swing RL = 50 kΩ
- 0.1 V
- Gain
- 100 V/V
- Gain Error VDIFF = 0
- 0.4 %
- VDIFF = −300 mV to
- 1 %
- Average Gain Drift TA = 0°C to 70°C
- 12 ppm/°C
- Bandwidth
- 2 kHz
- RFI Filter Cutoff (Each Input)
- 1 MHz
- Average TC TA = 0°C to 70°C
- 5 µV/°C
- Common-Mode Rejection Ratio CMRR VCM = 0.5 V to 2.5
- 100 dB
- Power Supply Rejection Ratio
- 100 dB
- Gain Bandwidth Product
- 100 kHz
- Slew Rate
- 0.02 V/µs
- Integrator Input Resistor
- 150 kΩ
- Offset Error VOS RL > 50 kΩ
- 1 mV
- Low
- 1.24 V
- High
- 1.35 V
- Supply Range
- 3.5 V
Performance
- Input Bias Current
- 50 pA
- Input Offset Current
- 25 pA
- Peak-to-Peak Voltage Noise f = 0.1 Hz to 10 Hz
- 12 µVp-p
- Input Voltage Range TA = 0°C to 70°C
- 0.2 V
- Short-Circuit Current
- 6.3 mA
- Offset Voltage
- 1 mV
- Input Voltage Range
- 0.1 V
- Large Signal Voltage Gain
- 110 dB
- Output Voltage Range RL = 50 kΩ
- 0.1 V
- Short-Circuit Current Limit
- 12 mA
- Voltage Noise Density (RTI) en f = 1 kHz
- 60 nV/√Hz
- Peak-to-Peak Voltage Noise (RTI) en p-p f = 0.1 Hz to 10 Hz
- 6 µVp-p
- Voltage Range RL = 50 kΩ
- 0.1 V
- Quiescent Supply Current
- 170 µA
- Shutdown Current
- 40 nA
Specifications & documentation
Use the official manufacturer documentation to verify electrical characteristics, package dimensions and operating limits before design approval.
Frequently asked questions
Common pre-quotation questions and selection notes to help you verify key parameters and sourcing before requesting a quote.
How do I verify the part is genuine / avoid counterfeit?
Buy only from authorized or franchised channels. On receipt, check: (1) laser-etched markings that solvent will not remove; (2) batch / lot code consistent between label and device; (3) original reel or tube packaging; (4) request traceability documents (CoC, date code). For critical parts, third-party X-ray / decapsulation testing is recommended.
How do I read the markings / date code on a chip?
Most active ICs use a 4-digit date code YYWW (year + week, e.g. 2345 = 2023 week 45). The top mark is manufacturer logo + base part number + lot code. For SMD code lookup, search by "marking code + package" on AllDataSheet / Octopart / LCSC.
What does the package code mean (TO-220, SOT-23, QFP…)?
Package codes describe the physical form factor and pin layout — critical when sourcing, because electrically equivalent parts in different packages will not fit the PCB. Common: TO-220 (3-terminal power), SOT-23 (3-pin small signal), DIP / SOIC (through-hole / SMD ICs), QFP / QFN (MCUs, processors).
What if my original model is discontinued (EOL / NRND)?
Three options: (1) the manufacturer’s recommended replacement; (2) franchised distributor legacy stock; (3) a functionally compatible cross-brand part — provided pinout and key parameters match. Always evaluate on a real board before mass swap.
What is the minimum order quantity (MOQ) and lead time?
We support both sample and volume orders. Minimum order quantity, stock availability and lead time are confirmed per inquiry — tell us your model and quantity and we will quote. Sample quantities for design validation are supported.
Can I get the datasheet and samples?
The full datasheet is linked on this page. For parts without a direct datasheet, we can locate the manufacturer document on request. Sample requests are supported — contact us with your model and quantity.
Request confirmation of current stock, date code, packaging, price and delivery terms. Product information does not constitute a binding offer; final specifications are confirmed with your quotation.