BL24C04F-PARC
BEILING · Memory (EEPROM/Flash)
Isometric preview; switch to top or 3D.
SOIC-8 · Generic package illustration
Based on the catalogue package field; not verified for this part. Check manufacturer documentation for dimensions, polarity and pinout.View part documentation ↓- Package
- SOP-8
Product overview
BEILING Memory (EEPROM/Flash) BL24C04F-PARC is a genuine original component suitable for circuit design and volume procurement. We supply full specifications, datasheets and flexible pricing, supporting both prototype and long-term supply.
- Manufacturer
- BEILING
- Part number
- BL24C04F-PARC
- Category
- Memory (EEPROM/Flash)
- Package
- SOP-8
- Condition
- New & Original
- Lifecycle
- Confirm with manufacturer
- Lead time / MOQ
- Confirm with quotation
Technical parameters
28 parametersConstruction
- Input Low Level
- 0.3
- Output Low Level VCC=1.7V
- 0.2
- Output Low Level VCC=5.0V
- 0.4
- Input/Output Capacitance(SDA)
- 8 pFVIO=0V
- Input Capacitance(A1,A2,SCL)
- 6 pFVIN=0V
- BL24C04FE1 TA =-40℃ to +105℃
- 2.5V to +5. 5V@1MHz
- Clock Frequency, SCL fSCL
- 1000 kHz
- Clock Pulse Width Low tLOW
- 0.5 μs
- Clock Pulse Width High tHIGH
- 0.26 μs
- Noise Suppression Time tI
- 50 ns
- Clock Low to Data Out Valid tAA
- 0.45 μs
- tBUF
- 0.5 μs
- Start Hold Time tHD:STA
- 0.26 μs
- Start Setup Time tSU:STA
- 0.26 μs
- Data In Hold Time tHD:DAT
- 0 μs
- Data In Setup Time tSU:DAT
- 50 ns
- Stop Setup Time tSU:STO
- 0.26 μs
- Data Out Hold Time tDH
- 50 ns
- Write Cycle Time tWR
- 3 ms
- 5.0V,25℃,Byte Mode(1) Endurance
- 1M Cycle
- 20 ns and le
- 300 n
- Input rise a
- 50 ns
- BL24C04F 4K
- 12×8)
- BL24C04F 4K bits (
- 512×8)
Performance
- Supply Voltage
- 5.5 V@400kHz
- Supply Current VCC=5.0V
- 0.14
- Input Leakage Current
- 0.10
- Output Leakage Current
- 0.05
Specifications & documentation
Use the official manufacturer documentation to verify electrical characteristics, package dimensions and operating limits before design approval.
Frequently asked questions
Common pre-quotation questions and selection notes to help you verify key parameters and sourcing before requesting a quote.
How do I verify the part is genuine / avoid counterfeit?
Buy only from authorized or franchised channels. On receipt, check: (1) laser-etched markings that solvent will not remove; (2) batch / lot code consistent between label and device; (3) original reel or tube packaging; (4) request traceability documents (CoC, date code). For critical parts, third-party X-ray / decapsulation testing is recommended.
How do I read the markings / date code on a chip?
Most active ICs use a 4-digit date code YYWW (year + week, e.g. 2345 = 2023 week 45). The top mark is manufacturer logo + base part number + lot code. For SMD code lookup, search by "marking code + package" on AllDataSheet / Octopart / LCSC.
What does the package code mean (TO-220, SOT-23, QFP…)?
Package codes describe the physical form factor and pin layout — critical when sourcing, because electrically equivalent parts in different packages will not fit the PCB. Common: TO-220 (3-terminal power), SOT-23 (3-pin small signal), DIP / SOIC (through-hole / SMD ICs), QFP / QFN (MCUs, processors).
What if my original model is discontinued (EOL / NRND)?
Three options: (1) the manufacturer’s recommended replacement; (2) franchised distributor legacy stock; (3) a functionally compatible cross-brand part — provided pinout and key parameters match. Always evaluate on a real board before mass swap.
What is the minimum order quantity (MOQ) and lead time?
We support both sample and volume orders. Minimum order quantity, stock availability and lead time are confirmed per inquiry — tell us your model and quantity and we will quote. Sample quantities for design validation are supported.
Can I get the datasheet and samples?
The full datasheet is linked on this page. For parts without a direct datasheet, we can locate the manufacturer document on request. Sample requests are supported — contact us with your model and quantity.
Request confirmation of current stock, date code, packaging, price and delivery terms. Product information does not constitute a binding offer; final specifications are confirmed with your quotation.